Activity Stream - Scream And Fly Powerboat and High Performance Powerboating Discussion Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs

Today, 07:40 PM

TraceF3 replied to a thread FVRC - Tavares FL - March 19-21 2021 Event Cancelled in Outboard and Racing History

Wow! 2800 HP ;) Love it. Gorgeous.

16 replies | 271 view(s)

Today, 07:38 PM

ShadowFlier replied to a thread 225 pmx been sitting in Technical Discussion

Ground one terminal on vst pump, run a wire from the other lead to the purple wire off the engine harness. When you turn the key to "on" the pump...

8 replies | 63 view(s)

Today, 07:21 PM

25two.stroke replied to a thread 225 pmx been sitting in Technical Discussion

Test light isnt the best unless it is one of the fancy ones that show voltage...you gotta make sure you have 12+ volts. Even so, a bad wire could...

8 replies | 63 view(s)

Today, 07:19 PM

dagodiver replied to a thread 12" Mid question.? in Technical Discussion

Thank you! Dago

13 replies | 270 view(s)

Today, 07:17 PM

25two.stroke replied to a thread swept lu in General Boating Discussion

I don't really understand the question, so here is an attempt: Mercury offered swept skegs and straight skegs in performance motors. Straights...

1 replies | 82 view(s)

Today, 07:16 PM

KIRCHNER replied to a thread 225 pmx been sitting in Technical Discussion

so put a test light between the 2 fuel pump wires? can i leave them connected? i have a brucato acu. if that means anything. if i have power that...

8 replies | 63 view(s)

Today, 07:11 PM

25two.stroke replied to a thread Seized Steering Tube Bolt in Technical Discussion

I got one sitting in the back of my truck rn stuck in a tilt tube. I just swap the tilt tubes and forget about it. There's another one at the shop...

30 replies | 314 view(s)

Today, 07:08 PM

25two.stroke replied to a thread 225 pmx been sitting in Technical Discussion

Driver, he is referring to the fuel pump driver circuit in the ECU. Yes, with key on the high pressure pump should run for 20 or 30 seconds I...

8 replies | 63 view(s)

Today, 07:07 PM

CDave replied to a thread ...been there... in The Scream And Fly Lounge

That cop with the tire width issues would have a field day down here with the 4x4's. :D I can say any time a cop has done a u-turn for me it...

6 replies | 205 view(s)

Today, 07:03 PM

KIRCHNER replied to a thread Seized Steering Tube Bolt in Technical Discussion

you lucked out. i was not so lucky, never got it out.

30 replies | 314 view(s)

Today, 06:55 PM

KIRCHNER replied to a thread 225 pmx been sitting in Technical Discussion

cowl is still on. i have a gauge, but i always heard some pump noise. my 2.4, laser i hear the pump, key on. how can plugs foul by sitting?

8 replies | 63 view(s)

Today, 06:54 PM

shadowcat replied to a thread FVRC - Tavares FL - March 19-21 2021 Event Cancelled in Outboard and Racing History

looks great- we miss you at the events and lunch at the Tiki Bar there- LOL

16 replies | 271 view(s)

Today, 06:48 PM

KIRCHNER replied to a thread 225 pmx been sitting in Technical Discussion

what is a driver? with key on, fuel should squirt from shrader, yes?

8 replies | 63 view(s)

Today, 06:46 PM

FUJIMO replied to a thread Seized Steering Tube Bolt in Technical Discussion

...my extensive ex-saltwater merc v-6 clamp working experience went with the above. out in 60 seconds. just make sure you have an 80 gallon upright...

30 replies | 314 view(s)

Today, 06:42 PM

KIRCHNER replied to a thread Seized Steering Tube Bolt in Technical Discussion

what i read was, he thought it had to move, to install hyd steering. he clearly said that. as long as the tube tilts not seized, i would leave it,...

30 replies | 314 view(s)

Today, 06:41 PM

FUJIMO replied to a thread Seized Steering Tube Bolt in Technical Discussion

30 replies | 314 view(s)

Today, 06:34 PM

FUJIMO replied to a thread Inline 6 merc vs's omc v4 crossflow production numbers in General Boating Discussion

...seems pretty accurate to me...thanks dave...

2 replies | 111 view(s)

Today, 06:16 PM

roadkill636 replied to a thread Sellers not replying to ???"s in Outboard Engines

Some of us old guys don't have thoes fancy new computer phones that ring and let us know immediately when someone posts "is this still available " ...

6 replies | 300 view(s)

Today, 06:14 PM

roadkill636 replied to a thread Sellers not replying to ???"s in Outboard Engines

If you ask "is this still available" you won't get a responce

6 replies | 300 view(s)

Today, 06:12 PM

roadkill636 replied to a thread Sellers not replying to ???"s in Outboard Engines

If a whole mot is for sale. Don't ask for just the powerhead. If I have a 1986 Chevy 1500 truck for sale don't ask if I will sell just the 350 in it.

6 replies | 300 view(s)

Today, 06:12 PM

25two.stroke replied to a thread Seized Steering Tube Bolt in Technical Discussion

Put in nicer words to keep this site "work friendly" : Remove steering rod and replace with new one. He was asking for advise on how to do this. ...

30 replies | 314 view(s)

Today, 06:09 PM

roadkill636 replied to a thread 225 pmx been sitting in Technical Discussion

Do you have a fuel pressure gauge at the rail? Whats it reading?. Could have fouled the plugs if too much oil in fuel and been sitting

8 replies | 63 view(s)

Today, 06:05 PM

KIRCHNER replied to a thread Seized Steering Tube Bolt in Technical Discussion

SO, lets beat it to death, mushroom the ends out, more heat, bigger hammer. so we can put it back the way it was when we started. lets think about...

30 replies | 314 view(s)

Today, 05:55 PM

rock replied to a thread 225 pmx been sitting in Technical Discussion

Fuel pump should run for a few seconds. If not probably the driver. I know there is a way to bypass by adding a ground wire but you need to talk to...

8 replies | 63 view(s)