Activity Stream

Anyone have any interest in buying my Allison? The power head is fresh, bought from a friend of Tony Brucato! It has a new Brucato ecu, 15" mid, off...

So hearing about the plastic cage bearings and how it's best to replace with metal cage. I have a set of clean 2.0 pistons and rods I got in a pile...

Natalie (suspiciously) drowned after falling off a boat moored off the coast of Catalina Island, California.

This is a house that I bought with intentions of tearing it down and building on the lot because its location and fact that it has a 3 car garage...

Just got this motor on a 1969 Magnum missile..don't know another about this motor..looks original..any info would help..have not tried to start it or...

are all the early mid 90s merc heads interchangeable for the 2.0 2.4 2.5 blocks ? I see a few variations with the part numbers also some stampings...

This is especially good for some of you younger members. An era before the cookie cutter boat models and Glastron, who many only know as an...

It’s time …. The boat is a 1997 Skater 28 - I think I’m the third owner. The boat was re-rigged with 2005 300X’s in 2007/2008 by the original...

Unless you are strapped into a safety capsule or cockpit and cannot turn around to see the trim angle of the engine, why would you trust reading the...

I have a 20 xd bullet project I would like to sell. Anyone interested. I think the boat is around the 1995 year. Needs some fiber glaß work. No...

Hi guys, first time poster. You are probably sick of seeing threads like this, I have searched and searched and I can't find any solid answers, so i...

Coil part #300-8M0077471 from Mercury is $188 and the same coil from DB Electrical is $45. My question is should I bite the bullet and buy the Merc...

I'll be there from Thursday afternoon until Sunday morning. I'll be shooting photos and videos, and running two live streams during the entire...

Is there a Better choice on a 2.5 liter/200--Less compression( factory CC ) and 25 degrees or 34 CC heads and say 23 degrees of timing. I believe ...

Totally new idea... https://electrek.co/2023/11/29/hyundai-kia-introduce-new-uni-wheel-drive-system-revolutionize-ev-design/

Hello All, So I want a new VKing, If you add all the material needed to restore a hull, then add the cost of new paint, interior and hardware I...

Does anyone have any contact info for Brad Collins? Thanks

looking for a clean small prop shaft out of a sporty or cle

Nice set of USED light weight Wizard forged Racing pistons with new wrist pins . On scale of 1-10 10 being new these are an 8 IMO ….$350.00 plus the...

1995 stv euro. 2002 2.5 280. Sportmaster lower unit. 20” offshore mid, fresh powder coat. New trim pump. Updated gauges, steering wheel. Very clean...

Are the prop shafts in a 2.5 Mercury outboard case and an Alpha one case basically the same? Would the ratcheting system fit a 2.5 prop shaft. I...

Looking to try a small cleaver on a Mercury inline project. Must be 14 inches in diameter or slightly less, 3 blades, 15 spline, small shaft, RH...

2005 28 skater , carbon Kevlar boat 2018 300xs motors with about 70hours brand new Zieger steering , tanks done at skater , new transom built for...

In reading about Optimax compressors, there was a change in or about 2010 but I cant find what exactly was changed or upgraded and was/ is the...

h]

*Garage Kept *Mercury VesselView & Dual Simrads: One for Driver, One for Throttles so both stay in the know *2021 Mercury 300r w/Sportmaster 1.75...

Mercury 2.5 race parts! 260 heads have been cut for 155 psi..$300 timming/throttle bracket for crankcase injected(horn) engine $100 reed plate...