Activity Stream - Scream And Fly Powerboat and High Performance Powerboating Discussion Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs

Today, 02:27 AM

Old boy replied to a thread Mercury Through The Years... in Outboard and Racing History

mmm, looks like a rudder set up on the Hydro!

21117 replies | 1376737 view(s)

Today, 02:07 AM

Capt.Insane-o replied to a thread Mercury Tech: WTH is up with this piston??? in Technical Discussion

Pre FP piston. Time to get the mill fired up.

1 replies | 38 view(s)

Today, 01:54 AM

Forkin' Crazy replied to a thread Tunnel hull pulling extremely hard to the right despite cambered skeg. in General Boating Discussion

Some props pull more than others. That sounds excessive though. Post some pictures of the lower, etc.

5 replies | 286 view(s)

Today, 01:50 AM

NZ Sidewinder replied to a thread Sidewinder/Panther complete restoration plus a bit. in Boat Build-Ups and Restorations

Basically the Hull is fully glassed now with just the bottom to finish the Pad and blueprint. Then full paint etc. The whole time Ive been dreading...

18 replies | 621 view(s)

Today, 01:01 AM

Z06man replied to a thread Tunnel hull pulling extremely hard to the right despite cambered skeg. in General Boating Discussion

Sounds like you may have blown the gasket under the water pump. After that they overheat at idle try trimming all the way under it may help slightly.

5 replies | 286 view(s)

Today, 12:59 AM

Forkin' Crazy replied to a thread Hull paints in Fiberglass and Composites Discussion

I like AwlGrip if you are using paint.

2 replies | 49 view(s)

Today, 12:38 AM

265mercman replied to a thread lower unit stuff in Lower Units

Got any coned cases in there? Iam need a few the drive shafts 20inch? If so ill take 3 driveshafts.. propshafts with gears a complete decent set? If...

2 replies | 117 view(s)

Today, 12:29 AM

at100plus replied to a thread Lifeline (Large) Used clean good condition- not certified. in Misc. Parts and Accessories

Glad you like it. Enjoy!

5 replies | 356 view(s)

Today, 12:20 AM

Forkin' Crazy replied to a thread Post your Favorite Memes Here in The Scream And Fly Lounge

5584 replies | 575983 view(s)

Today, 12:09 AM

Capt.Insane-o replied to a thread Alpha SS lower unit in Technical Discussion

It's a alpha spool type shift mechanism so you absolutely must have a shifter that locks into each gear.

3 replies | 93 view(s)

Yesterday, 11:52 PM

rgsauger started a thread Mercury Tech: WTH is up with this piston??? in Technical Discussion

V200 - 2.4 So I'm ordering rings tonight and realize that one of my pistons is different from the rest - it's the #1 as marked. It's .010" over -...

1 replies | 38 view(s)

Yesterday, 11:51 PM

Scream And Fly replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

Welcome to S&F! You’ll find that there are hundreds of members here that have a Promax and that’s because they are just a fantastic engine...

107 replies | 4020 view(s)

Yesterday, 11:40 PM

outboards4life replied to a thread Mercury Tech: Installing piston pin in Technical Discussion

Is there a part number for this?

8 replies | 202 view(s)

Yesterday, 11:22 PM

rgsauger replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

Welcome to S&F EH2000. 225 PM is a great motor

107 replies | 4020 view(s)

Yesterday, 11:16 PM

Eh2000 replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

I just had a 225 ProMax rebuilt because the 4 Stroke engines are too heavy for my hull. I would much prefer a 4 Stroke with an alternator. ...

107 replies | 4020 view(s)

Yesterday, 11:04 PM

rgsauger replied to a thread Mercury Tech: Installing piston pin in Technical Discussion

Thanks all for your feedback and ideas. I like the idea on the deep well socket, Rock, and the hot/cold, Roadkill. Very good detail on the clip, 99.

8 replies | 202 view(s)

Yesterday, 11:01 PM

KIRCHNER replied to a thread 5 Gallon Fuel Jug Caps in General Boating Discussion

GET out the pipe wrench/////

7 replies | 253 view(s)

Yesterday, 10:59 PM

rgsauger replied to a thread Wh12 vs wh29 carbs? in Technical Discussion

I'm waiting for some smart-ass to say "17"! Lol Granted, I'm not that guy. Just saying... Seriously good luck figuring out.

2 replies | 97 view(s)

Yesterday, 10:56 PM

THUNDERSTRUCK131 started a thread Scream and Fly Facebook in Computer and Forum Support

On the Scream and Fly facebook page I posted asking if anyone had experience machining the prop shaft side of a SRX prop to fit a Merc small and do...

0 replies | 35 view(s)

Yesterday, 10:47 PM

Bodhi replied to a thread 5 Gallon Fuel Jug Caps in General Boating Discussion

Same damn thing with my tapered top vp jug, im at the 2 hand stage now. Silicone isn't helping anymore

7 replies | 253 view(s)

Yesterday, 10:46 PM

rgsauger replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

That is CRAP, wildman!!! I would be livid if I dropped big coin on a motor, lost a prop, and then the company said "sucks to be me". Sorry to hear...

107 replies | 4020 view(s)

Yesterday, 10:34 PM

Greg G replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

JPEROG why won't Merc cover the broken prop shafts under warranty? That is the only thing that seems strange IMO.

107 replies | 4020 view(s)

Yesterday, 10:33 PM

gmorgan replied to a thread Forward gear bearing large or small in Technical Discussion

You were correct, Tex. It is no ratcheting and small bearing.

3 replies | 105 view(s)

Yesterday, 10:30 PM

JPEROG replied to a thread Four Stroke outboards have changed the performance boating landscape in General Boating Discussion

If guys don't get this message, then you are missing the point. Randy runs the hell out of boats but also has "some" common sense as to when and how...

107 replies | 4020 view(s)

Yesterday, 10:14 PM

FUJIMO replied to a thread Mercury Through The Years... in Outboard and Racing History

21117 replies | 1376737 view(s)