Activity Stream - Scream And Fly Powerboat and High Performance Powerboating Discussion Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs

Today, 10:02 PM

Will hedrick replied to a thread Post your Favorite Memes Here in The Scream And Fly Lounge

7243 replies | 1195563 view(s)

Today, 09:28 PM

Asstracker replied to a thread Which is the Less Evil in Technical Discussion

agreed

3 replies | 336 view(s)

Today, 09:26 PM

Asstracker replied to a thread 1647-5675 housing in Technical Discussion

Pretty sure they're pinned after the damage. I dont recal ever hearing of anyone doing it for preventative reasons but i could be wrong

3 replies | 88 view(s)

Today, 09:24 PM

lars strom replied to a thread Hot Singles ! - Pictures in Outboard and Racing History

I think this is the ON Molinari tunnel Renato & Cesare Scotti won Paris 6 Hours 1966.

5201 replies | 1514858 view(s)

Today, 09:23 PM

Asstracker replied to a thread Prop and gear question. in Technical Discussion

I forget from when i did it, but i think some of the sporty stuff was the same as the alpha ones, im not sure what as this was a bit ago and i only...

2 replies | 213 view(s)

Today, 08:58 PM

David - WI replied to a thread 1.2 million Cybertruck's in The Scream And Fly Lounge

There was a Munroe/Musk YouTube cybertruck video today that I skipped over https://m.youtube.com/watch?v=ky1Z2klPalw

46 replies | 2093 view(s)

Today, 08:51 PM

David replied to a thread 1.2 million Cybertruck's in The Scream And Fly Lounge

The Cybertruck is steer by wire, and the initial reviews are positive. It will be interesting when fuller reviews are published and super...

46 replies | 2093 view(s)

Today, 08:32 PM

OnPad replied to a thread 2000 200HP Merc. 2.5 in Technical Discussion

Repurpose your head bolts, and replace at least the rod bolts. If you weigh the rods and pistons separate, you'll likely build a better balanced...

15 replies | 829 view(s)

Today, 08:32 PM

David - WI replied to a thread 1647-5675 housing in Technical Discussion

Did they ever "pin" them when they coned or rebuilt them, to prevent damage or only after the carrier spun? I still have one coned case with the...

3 replies | 88 view(s)

Today, 08:23 PM

David - WI replied to a thread Mech trim gauges in Props, Setup, and Rigging

Hardin has about 10 different (insanely-priced) mechanical actuator kits with photos, you might get ideas from? ...

1 replies | 49 view(s)

Today, 08:21 PM

doug7488 replied to a thread Post your Favorite Memes Here in The Scream And Fly Lounge

7243 replies | 1195563 view(s)

Today, 07:53 PM

oldschoolltv replied to a thread Upcoming Event: Camp Mack River Run Christmas Party - December 7-8-9. in General Boating Discussion

5 replies | 658 view(s)

Today, 07:41 PM

tlwjkw replied to a thread heads in Technical Discussion

don't think it was confusion on my part.. was jus an old head that can't read and comprehend $hit right anymore..... understand usin' up what...

29 replies | 848 view(s)

Today, 07:29 PM

Mrzip replied to a thread 2000 200HP Merc. 2.5 in Technical Discussion

Put Together With New Bearings Rod Bolts. Hammer On It :D

15 replies | 829 view(s)

Today, 07:26 PM

OnPad replied to a thread heads in Technical Discussion

I will clarify any confusion I may have caused. A person can run any lesser displacement head on a larger displacement block. 2.4 heads being a bit...

29 replies | 848 view(s)

Today, 07:24 PM

skialot2 replied to a thread 2000 200HP Merc. 2.5 in Technical Discussion

I got my block back from the machine shop today. I had 3 cylinders bored .015 oversize. And had all 6 honed. It came out great. Just one little mark...

15 replies | 829 view(s)

Today, 07:23 PM

tlwjkw replied to a thread 1647-5675 housing in Technical Discussion

i'd scrape it.. mainly cause it had ta have tha carrier pinned for some unknown reason....

3 replies | 88 view(s)

Today, 07:23 PM

oper600 replied to a thread Pair of 2.5 Alien Skirts in Misc. Parts and Accessories

Ttt - price lowered

1 replies | 288 view(s)

Today, 07:21 PM

Stoker boy replied to a thread heads in Technical Discussion

You guys are getting above my pay grade, I’ll be quiet now.

29 replies | 848 view(s)

Today, 07:16 PM

Tmasse24 started a thread WANTED: OMC 16” Taylor Mid in Parts Wanted

Looking for a 16” OMC Taylor Mid for a V4 Crossflow build. Let me know what you have

0 replies | 38 view(s)

Today, 07:14 PM

tlwjkw replied to a thread heads in Technical Discussion

tha 2.4 second gen head will run ona fat block but a fat block head will not run ona second gen block... thought it was said that you can run a fat...

29 replies | 848 view(s)

Today, 07:11 PM

Stoker boy replied to a thread heads in Technical Discussion

The outer thickness of the brown line is the inside sealing area of the gasket. It seems like the metal ring on the gasket might not have a good seal...

29 replies | 848 view(s)

Today, 07:09 PM

lars strom replied to a thread Facts about Evinrude/Johnson racing outboards made my OMC in Outboard and Racing History

Inside Cees Van Der Velden's racing service van in Drammen, Norway 1980.

12080 replies | 3727794 view(s)

Today, 07:07 PM

Stoker boy replied to a thread heads in Technical Discussion

29 replies | 848 view(s)