User Tag List
Thanks: 0
Results 1 to 8 of 8
Thread: merc chopper
-
01-01-2018, 05:46 PM #15000 RPM
- Join Date
- Mar 2006
- Location
- auckland new zealand
- Posts
- 655
- Thanks (Given)
- 3
- Thanks (Received)
- 9
- Likes (Given)
- 6
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
merc chopper
Hey guys can any one tell me some info on the merc choppers.
Im running merc et props but want to try for somthing with more bow lift so looking at the chopper.
If im running a 26et would it be same revs as a 26 chopper brand new flo torq type.
As i know with some of the other props merc dose they say you need to go up or down in pitch to run the same revs
-
01-01-2018, 07:41 PM #2Screaming And Flying!
- Join Date
- Mar 2008
- Location
- Tourist Trap, Florida
- Posts
- 14,753
- Thanks (Given)
- 381
- Thanks (Received)
- 1302
- Likes (Given)
- 5602
- Likes (Received)
- 11031
- Mentioned
- 2 Post(s)
- Tagged
- 1 Thread(s)
I run a 28 chopper big blade and a 28 ET 3 blade and get very close to the same r's. ET may run a few more.
83 V-King, 96 Mariner, 200 hp ff block 2.5 w/a 28p choppa
We gotta clean this liberal mess up, VOTE TRUMP TO MAGA!
Rebuild thread:
http://www.screamandfly.com/showthre...-it&highlight=
http://www.screamandfly.com/showthre...cs.&highlight=
Videos
-
01-02-2018, 12:10 PM #31980 Cougar 19 tunnel,90 2.4L Bridgeport EFI in middle of restoration.
1988 BAJA Sunsport 186, 96 225 Pro Max
79 12' Auminum, 95 Merc 9.9
RIP Stu
"So many idiots, so few bullets"
-
02-02-2018, 10:21 PM #4Member
- Join Date
- Jul 2010
- Location
- edmonton Alberta
- Posts
- 48
- Thanks (Given)
- 0
- Thanks (Received)
- 3
- Likes (Given)
- 2
- Likes (Received)
- 11
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
304Mirage liked this post
-
02-02-2018, 10:42 PM #5
Bottom pic is a through hub cleavers, stern drive prop. Top pic is a chopper.
Dave1980 Cougar 19 tunnel,90 2.4L Bridgeport EFI in middle of restoration.
1988 BAJA Sunsport 186, 96 225 Pro Max
79 12' Auminum, 95 Merc 9.9
RIP Stu
"So many idiots, so few bullets"
-
02-02-2018, 11:29 PM #6Member
- Join Date
- Jul 2010
- Location
- edmonton Alberta
- Posts
- 48
- Thanks (Given)
- 0
- Thanks (Received)
- 3
- Likes (Given)
- 2
- Likes (Received)
- 11
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I know, I couldn't get the pics to follow the words, and could get them to move on an edit. The pic of the chopper even has chopper written on the tag.
I've only seen three chopper props out this way in 40 yrs. It is fun to watch how the motor spins up and with great slippage the boat slowly moves, then Wham, it's going
-
02-03-2018, 12:23 AM #7
I would give the $75 for that chopper
-
03-07-2018, 12:16 PM #86000 RPM
- Join Date
- Feb 2011
- Location
- HUDSON, FLORIDA
- Posts
- 1,530
- Thanks (Given)
- 433
- Thanks (Received)
- 64
- Likes (Given)
- 435
- Likes (Received)
- 452
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
I RUN a 24 scorpion 15'' dia thru-hub super lift all around same rpm as 26 chopper; super hi-rake design same top end as chop without the steer torque. lots of guys say they love em. takes flo-tork hub.
Similar Threads
-
13ft delta 60 merc looking for 18 pitch stainless chopper prop 13 spline 60hp merc
By boogie in forum Props, Setup, and RiggingReplies: 6Last Post: 07-14-2019, 11:48 AM -
Merc 24P big ear chopper and cut 28P chopper
By lbhsbz in forum PropellersReplies: 1Last Post: 02-02-2017, 08:05 PM -
what's the difference between a merc chopper and a merc inline chopper?
By syclone01 in forum General Boating DiscussionReplies: 10Last Post: 03-09-2011, 03:56 PM