User Tag List
Results 16 to 25 of 25
Thread: Dual pvs holes
-
10-20-2017, 05:44 AM #16
it is amazing what the vents do.
I have had props that are just terrible for trying to get out the hole, vent them and hang on for dear life ha ha
violent is perfect word for when its right, I have one I recently done and violent is the perfect way to describe it.
atleast you know those big holes are working good for you,.
a low pitched prop with vents would rip a few skiers out the hole very good, just need to make sure the transom is up to the job of
getting the power on the prop so fast.
-
Bullet 20cc liked this post
-
10-20-2017, 10:47 AM #17
I just had 1 prop milled. It has 1 7/8vent holes and another pvs hole next to it!
Hopefully the 7/8" is not too big.already!
-
10-20-2017, 11:39 AM #1896 Bullet 20cc, Yamaha OX 250+, 10" jack, labbed 30" Bravo LH w/1.25" exhaust pipes, counter rotating Bob's lower...it goes faster when you spin it the other way...
02 Dodge Cummins 2500 reg cab 4x4, converted long to short bed, up a foot, twins, injectors, fully built auto, dyno'd 582hp/1015tq
99 Dodge Viper GTS Coupe, 8.0L V-10, lowered 1", Corsa pipes/no cats, 450hp/500tq
-
10-20-2017, 11:45 AM #1996 Bullet 20cc, Yamaha OX 250+, 10" jack, labbed 30" Bravo LH w/1.25" exhaust pipes, counter rotating Bob's lower...it goes faster when you spin it the other way...
02 Dodge Cummins 2500 reg cab 4x4, converted long to short bed, up a foot, twins, injectors, fully built auto, dyno'd 582hp/1015tq
99 Dodge Viper GTS Coupe, 8.0L V-10, lowered 1", Corsa pipes/no cats, 450hp/500tq
-
10-27-2017, 01:17 AM #20
Had it in the water yesterday.It slips up to 3000rpm. So luckily the 7/8 was not too big already.
-
10-27-2017, 01:45 AM #21
Was it working for you or are you thinking about more?
Last edited by Bullet 20cc; 10-27-2017 at 02:01 AM.
96 Bullet 20cc, Yamaha OX 250+, 10" jack, labbed 30" Bravo LH w/1.25" exhaust pipes, counter rotating Bob's lower...it goes faster when you spin it the other way...
02 Dodge Cummins 2500 reg cab 4x4, converted long to short bed, up a foot, twins, injectors, fully built auto, dyno'd 582hp/1015tq
99 Dodge Viper GTS Coupe, 8.0L V-10, lowered 1", Corsa pipes/no cats, 450hp/500tq
-
10-27-2017, 05:17 PM #22
Works great. Might try to open up the pvs plugs a bit.
-
11-03-2017, 04:40 PM #23
they should re-name the big holes Launch control holes ha ha
-
Bullet 20cc liked this post
-
11-03-2017, 04:51 PM #2496 Bullet 20cc, Yamaha OX 250+, 10" jack, labbed 30" Bravo LH w/1.25" exhaust pipes, counter rotating Bob's lower...it goes faster when you spin it the other way...
02 Dodge Cummins 2500 reg cab 4x4, converted long to short bed, up a foot, twins, injectors, fully built auto, dyno'd 582hp/1015tq
99 Dodge Viper GTS Coupe, 8.0L V-10, lowered 1", Corsa pipes/no cats, 450hp/500tq
-
phillnjack thanked for this postphillnjack liked this post
-
07-02-2019, 05:52 AM #25Screaming And Flying!
- Join Date
- Jul 2004
- Location
- Connecticut
- Posts
- 6,009
- Thanks (Given)
- 465
- Thanks (Received)
- 168
- Likes (Given)
- 911
- Likes (Received)
- 951
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Older thread with a lot of good info!
Similar Threads
-
28P Hydromotive Quad 4 with flared barrel and dual PVS holes.
By 21xdc in forum PropellersReplies: 24Last Post: 08-15-2016, 08:14 PM -
WTB 28p Bravo with dual pvs holes
By KCBrains in forum Propellers WantedReplies: 9Last Post: 06-06-2016, 08:05 PM -
28" Bravo I with Dual PVS Holes
By 1122 in forum PropellersReplies: 3Last Post: 09-09-2014, 02:45 PM -
28 Bravo One with dual holes
By bretter in forum PropellersReplies: 4Last Post: 03-23-2014, 04:24 PM -
What is best product for filling in screw holes and guage holes? Thanks, Mike
By mragu in forum General Boating DiscussionReplies: 11Last Post: 12-31-2013, 08:12 PM