User Tag List
Results 61 to 75 of 139
-
08-12-2017, 07:43 AM #61
Thanks for looking Lynn, I appreciate it. I'm over at the machinist now to get the one block checked out, I'm not going to bore every cylinder if I don't have to
Last edited by mrcrsr; 08-12-2017 at 10:23 AM.
action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
-
08-16-2017, 08:56 AM #62
I just bought a crank, rods and pistons off eBay that have the correct pistons. They are 3 ring so I'll just run the upper 2 rings, if I can't buy a new set of pistons. I still need 2 .015 pistons though
action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
-
08-16-2017, 01:04 PM #63
I'll check at the marina in town. He has all kinds of nos stuff.
-
08-16-2017, 07:22 PM #64
Thanks Lynn!
action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
-
08-16-2017, 09:02 PM #65The Historic Photo Master
- Join Date
- Jan 2004
- Location
- Florida
- Posts
- 37,836
- Thanks (Given)
- 64
- Thanks (Received)
- 1667
- Likes (Given)
- 337
- Likes (Received)
- 19216
- Mentioned
- 3 Post(s)
- Tagged
- 0 Thread(s)
-
08-17-2017, 03:33 AM #66Screaming And Flying!
- Join Date
- Jun 2007
- Location
- Singapore/Melbourne/Italy
- Posts
- 9,109
- Thanks (Given)
- 1010
- Thanks (Received)
- 356
- Likes (Given)
- 4327
- Likes (Received)
- 1976
- Mentioned
- 8 Post(s)
- Tagged
- 0 Thread(s)
What pistons do the guys run the 4 cyl kneelers? Must be something new
-
08-17-2017, 05:42 AM #67
-
08-17-2017, 09:07 AM #68
-
mrcrsr liked this post
-
08-17-2017, 03:44 PM #69
Twister cranks had a habit of cracking and breaking off just under the flywheel, did a couple way back when. Make sure you get it crack tested
Peter Thomas
-
Mark75H thanked for this post
-
08-19-2017, 02:24 PM #70action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
-
Mark75H liked this post
-
08-23-2017, 11:58 PM #71
On the block with the stock crank you should use the inner cover and outer covers for the exhaust from your ADI block and with the stock midsection, you will have a tuned exhaust system .Also you will have to use the reed blocks to replace the bearing blocks on the the 3 positions they occupied in the ADI block unless you can get Dick Austin to make you some single roller bearings like he made for his I6 Looper . On the T2X crank block on a stock mid the exhaust tuning will be way out , on the T2 the top 3 cylinders dumped out the bottom of the block into a large open midsection while the bottom 3 cylinders dumped into a 10'' long passage inside the mid . the passage was about 2x2 inches inside . If you take the stock tuner out and fabricate a passage for the bottom 3 cylinders 8-10 inches long you may be able to get the exhaust tuning back, on this engine the exhaust iuning is what makes it special . I found a new oversize non power ported piston on ebay part # 776-8900A2 used in later 90 hp engines. Ebay # 112495872708 , $45 .Keep us posted on your progress !
-
08-24-2017, 06:53 PM #72
Thanks so much, just purchased it. I'm going to build the t2x as the first engine, and going to use adi ignition on it. When I go to start on the project I'll start posting on it. Got another piece of the puzzle today, the 15" midsection
action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
-
08-28-2017, 05:29 PM #73
I still need to find a .015 oversize piston, if anyone has one
action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
-
08-29-2017, 12:40 AM #74
Take a look at ebay # 361445044838 part # 745-7673A2 $85 or same part# at marineengine.com $82
Last edited by baldad45; 08-29-2017 at 12:44 AM.
-
08-29-2017, 06:11 AM #75action mobile marine, 772 528 0754, dealers for aces fuel products,wolf efi, pro marine,latham and gaffrig/livorsi. we build gearcases and modify them(3 litre) to ratchet, and powerheads as well. 21 skater/3 litre wolf efi 113 mph the engine build http://www.screamandfly.com/showthre...-3-litre-build
Similar Threads
-
Look at what I just picked up !
By outlaw 10.5 in forum General Boating DiscussionReplies: 20Last Post: 06-28-2016, 06:52 PM -
picked up a new toy!!!
By gettinwet in forum General Boating DiscussionReplies: 4Last Post: 08-18-2009, 05:20 PM -
Picked up my 92 Merc 245
By 91nitro in forum General Boating DiscussionReplies: 3Last Post: 06-05-2008, 09:36 AM -
Picked up my new car Sat.
By Ziemer in forum The Scream And Fly LoungeReplies: 9Last Post: 08-30-2005, 05:56 PM -
Picked up 700 RPM's today !
By BOUDREAUX in forum Technical DiscussionReplies: 2Last Post: 12-02-2003, 09:57 PM