User Tag List
Thanks: 0
Likes: 0
Results 1 to 10 of 10
Thread: Hydromotive 24" QIV X OT
-
02-18-2017, 06:56 PM #15000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Hydromotive 24" QIV X OT
24" Hydromotive Quad IV X OT. This is similar to a Mercury Trophy with the smaller hub for over and thru exhaust but it is 14-1/2" in diameter. It has the standard square hub to accept Mercury style hub kits. Has small 5/16" vent holes.
The leading edge and tips of each blade have some nicks that are generally less than 1/16" deep. There are also a few scratches but there are no dents, cracks, or big gouges. I'm not the original owner but I'm sure it has not been repaired or modified.
$325 includes PayPal fees, shipping and insurance to the 48 state area.
-
02-28-2017, 10:44 AM #25000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Still for sale
-
02-28-2017, 09:19 PM #3
any idea what type of boat this would work well on? I have a Spectre 24cc with a 350 verado.
-
02-28-2017, 10:00 PM #45000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I ran it briefly on a 21' Checkmate Pulsare. It was right between a 24" mod'd Bravo and a 24" Promax in hole shot and speed. I'm at high altitude and carry a heavy load. Although it is similar to a Trophy, it ran way better on my setup probably due to the larger diameter.
-
02-28-2017, 10:39 PM #5
what kind of speeds did you get with it?
-
02-28-2017, 10:52 PM #65000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Low 70s at about 5900 rpm but I didn't spend much time dialing it in with trim or engine height. I have 1.62 gears.
-
03-03-2017, 10:05 AM #76000 RPM
- Join Date
- Dec 2011
- Location
- Ottawa
- Posts
- 1,365
- Thanks (Given)
- 33
- Thanks (Received)
- 47
- Likes (Given)
- 20
- Likes (Received)
- 72
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
They work very well on allison xb 2003's kinda a trophy on steroids with bigger diameter
-
03-10-2017, 09:03 PM #8Junior Member
- Join Date
- Nov 2006
- Location
- Farwell, TX
- Posts
- 8
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
$300.00?
-
03-11-2017, 06:16 PM #95000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Yes, PM sent
-
03-12-2017, 05:10 PM #105000 RPM
- Join Date
- Jun 2002
- Location
- Northern Utah
- Posts
- 454
- Thanks (Given)
- 3
- Thanks (Received)
- 8
- Likes (Given)
- 7
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Sold---thanks
Similar Threads
-
Hydromotive Quad IV set 24"
By EWPE in forum PropellersReplies: 5Last Post: 09-07-2016, 07:05 PM -
26p 14 3/4" Dia Hydromotive 4-Blade, Over/Thru Hub
By G-Train in forum PropellersReplies: 8Last Post: 05-12-2015, 09:34 PM -
30" Hydromotive Quad IV OT
By nealxb2003 in forum PropellersReplies: 3Last Post: 11-06-2014, 07:21 PM -
Hydromotive props, do they do well surfaced 3" - 5"?
By roadkill636 in forum Technical DiscussionReplies: 0Last Post: 06-22-2009, 08:55 PM