User Tag List
Results 106 to 120 of 198
Thread: verado 350 sci JUNK!
-
02-10-2016, 03:01 AM #106
-
Mr. Demeanor liked this post
-
02-10-2016, 04:10 AM #1075000 RPM
- Join Date
- Mar 2006
- Location
- auckland new zealand
- Posts
- 655
- Thanks (Given)
- 3
- Thanks (Received)
- 9
- Likes (Given)
- 6
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
from just looking at your downloads from ecm you have very low water psi on most of them for what rpms you are pulling I think I have only seen one over 9psi
-
02-10-2016, 09:56 AM #108
First off - I am not at all familiar with verados. But, with the ECM reading low water pressure & the overheat warnings (not codes) could that be connected to going into a soft failsafe? ECM sees a potential problem ( low water press.) & attempts to protect the engine? Maybe it's holding rpm's back to what it "thinks" is safe for the water pressure it's reading. Since it's not actually overheating, maybe the pressure sensor is out of range/bad?
AIRWALK
gettin' old ain't for sissies
-
02-10-2016, 10:10 AM #109Member
- Join Date
- Jan 2016
- Location
- Missourj
- Posts
- 73
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 5
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Just got off the phone with brian.....they are telling me to Jake plate it that the motor needs to go up at least a other inch.....so I bought a 25k motor to spend another 1300 on a Jake plate....
Also I need a bravo fs prop....any 1 around here have one I could test
-
02-10-2016, 10:24 AM #110
You really need to get that boat & motor to a shop with setup experience that can really help or you will continue to spin your wheels, waste time and money on all types of trial an error stuff.....JMPO again!
-
02-10-2016, 10:25 AM #111
-
Baja170 liked this post
-
02-10-2016, 10:41 AM #112Member
- Join Date
- Jan 2016
- Location
- Missourj
- Posts
- 73
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 5
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
All ready emailed ken
-
02-10-2016, 11:47 AM #1135000 RPM
- Join Date
- Dec 2013
- Location
- georgia
- Posts
- 550
- Thanks (Given)
- 31
- Thanks (Received)
- 24
- Likes (Given)
- 57
- Likes (Received)
- 65
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I think most of you guys are missing key points on his problem. He has had two other motors with less horsepower and no jack plate on boat that gave better results. there is no way his setup is wrong. If you have Whipple ecm put it on motor and see what happens no need for 350 sei computer it's the same engine.
FYI drive boat like you stole it and hope you blow the motor it under warranty no need for attorney after that.
OR go back to dealer and tell them you want to trade in motor for a 400r they say nothing is wrong with your 350sei and you have less than 50hrs on it you should get just about what you paid for itLast edited by 2jz; 02-10-2016 at 11:49 AM.
-
David Borg liked this post
-
02-10-2016, 11:59 AM #114Member
- Join Date
- Jan 2016
- Location
- Missourj
- Posts
- 73
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 5
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Mercury is telling me it is due to the big diameter gear case....thinking about calling my dealer and just trading back for a 250 or 300...........and just be happy with it......2200 for a prop and jack plate......right now I am going to see if my gearcase from my 225 will work on it
-
02-10-2016, 12:08 PM #115Team Member
- Join Date
- Jul 2015
- Location
- NC/TN/KY
- Posts
- 1,056
- Thanks (Given)
- 94
- Thanks (Received)
- 104
- Likes (Given)
- 1322
- Likes (Received)
- 490
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
pTHis is complete BS. Good to know, I will be skipping Mercury and the Verado for sure from this point on.
-
quad143 liked this post
-
02-10-2016, 12:36 PM #1165000 RPM
- Join Date
- Jul 2009
- Location
- West Coast, FL
- Posts
- 330
- Thanks (Given)
- 1
- Thanks (Received)
- 6
- Likes (Given)
- 40
- Likes (Received)
- 24
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
quad143 liked this post
-
02-10-2016, 01:52 PM #117Member
- Join Date
- Jan 2016
- Location
- Missourj
- Posts
- 73
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 5
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
They seem to think it's all from drag. And told me aluminum boat is only designed to go so fast but my 225 with 300 computer put this motor in the dust
-
02-10-2016, 02:01 PM #118
Tell Lee Taylor, the guy with the Harvey Aluminum Special that. DO NOT trade it unless they will give you what you have out of pocket in it. If not, take 'em to the cleaners. Maybe not lemon law, a civil suit. With good documentation, & the time & expense it has taken from you - most judges side with the consumer. You should be able to get all the cash & compensation for time, IMO.
AIRWALK
gettin' old ain't for sissies
-
02-10-2016, 02:21 PM #119Member
- Join Date
- Jan 2016
- Location
- Missourj
- Posts
- 73
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 5
- Likes (Received)
- 2
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I can tell u they have someone that monitor these sites....I just laughed and said good
-
02-10-2016, 06:29 PM #120
OIC. The big case sucks up 100 hp???
Similar Threads
-
My new scarab w/verado , any upgrades on verado 250 ?
By cc@100mph in forum General Boating DiscussionReplies: 21Last Post: 08-03-2010, 06:28 AM -
Have ya'll seen this junk ?
By RB in NM in forum The Scream And Fly LoungeReplies: 0Last Post: 09-24-2009, 11:14 AM -
Mercury Marine and Mercury Racing Product Report: 300 Verado, 200 I-4 Verado, 1200SCi
By Scream And Fly in forum General Boating DiscussionReplies: 68Last Post: 02-21-2007, 07:56 AM