User Tag List
Thanks: 0
Likes: 0
Results 1 to 11 of 11
-
01-29-2015, 02:22 AM #15000 RPM
- Join Date
- Mar 2006
- Location
- auckland new zealand
- Posts
- 655
- Thanks (Given)
- 3
- Thanks (Received)
- 9
- Likes (Given)
- 6
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Heres one for ya 2.5merc ecu issues
I have 2x s3000 motors on spins left and the other right on a v bottom what I have happening is port motor just shuts down from time to time.
Now this is where it gets hard if I run my brucatos no issue at all.
Run merc ecms port motor plays up I have swapped them over and tried another set for good luck and it will just stop on me.
Since the first time to now I have replaced stators, triggers, rectifiers switch boxers.
All engine wiring.
Any thoughts will be great.
Thanks rick
-
01-29-2015, 02:33 AM #2Scream And Fly VIP
- Join Date
- Jul 2013
- Location
- California
- Posts
- 1,555
- Thanks (Given)
- 21
- Thanks (Received)
- 63
- Likes (Given)
- 83
- Likes (Received)
- 294
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Does it seem to be related to outside air temp?
-
01-29-2015, 02:35 AM #35000 RPM
- Join Date
- Mar 2006
- Location
- auckland new zealand
- Posts
- 655
- Thanks (Given)
- 3
- Thanks (Received)
- 9
- Likes (Given)
- 6
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
not to sure may be, was hot on sunday when I ran it
-
01-29-2015, 10:26 AM #4
were these 849849 ecu,s?
and did you run the ground wire from the casing to ground?
-
01-29-2015, 10:35 AM #5Scream And Fly VIP
- Join Date
- Jul 2013
- Location
- California
- Posts
- 1,555
- Thanks (Given)
- 21
- Thanks (Received)
- 63
- Likes (Given)
- 83
- Likes (Received)
- 294
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Had some issues with early digital ECU's shutting down when they got to hot. Outside temp of 95 plus equaled under cowl temp of 120 or so. ECU would just shut down then be fine once it cooled off. A lot like my iPad! Couldn't do anything to remedy it other then replacing the ECU.
-
01-29-2015, 01:20 PM #65000 RPM
- Join Date
- Mar 2006
- Location
- auckland new zealand
- Posts
- 655
- Thanks (Given)
- 3
- Thanks (Received)
- 9
- Likes (Given)
- 6
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Onetime Not sure of what ecus are on it but i never have issues on the starboard motor and can put either ecm on the starboard side and not one issue.
Pan Ronnie Earth cable is on the the lower ecu mount nut sitting on the casing
-
01-29-2015, 08:00 PM #7Screaming And Flying!
- Join Date
- Sep 2001
- Location
- shreveport,la
- Posts
- 5,706
- Thanks (Given)
- 6
- Thanks (Received)
- 118
- Likes (Given)
- 85
- Likes (Received)
- 773
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I'm confused. You can put the ecu on another motor and no problems? Your problem may be in the injector harness. Have you used a cleaner and brush on the ecu plug?
Erik Kiser
-
01-29-2015, 09:05 PM #8Scream And Fly VIP
- Join Date
- Jul 2013
- Location
- California
- Posts
- 1,555
- Thanks (Given)
- 21
- Thanks (Received)
- 63
- Likes (Given)
- 83
- Likes (Received)
- 294
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I'm confused too.
-
01-30-2015, 04:33 AM #95000 RPM
- Join Date
- Mar 2006
- Location
- auckland new zealand
- Posts
- 655
- Thanks (Given)
- 3
- Thanks (Received)
- 9
- Likes (Given)
- 6
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
So I have 849849 a10 merc on there today and what it did was went happy to 8k the port motor went back to 6400ish. put the brucatos on no issue
-
01-30-2015, 09:02 AM #10Scream And Fly VIP
- Join Date
- Jul 2013
- Location
- California
- Posts
- 1,555
- Thanks (Given)
- 21
- Thanks (Received)
- 63
- Likes (Given)
- 83
- Likes (Received)
- 294
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Leave the Brucatos on. Seems there is defiantly an issue with the Merc ecu.
-
01-30-2015, 08:13 PM #11Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
yes send them to me ill guard them carefully so no one else gets a hold of them