User Tag List
Results 61 to 75 of 77
Thread: Aluminum Drag Plates
-
09-12-2015, 08:40 PM #61
the BOB's plate is a waste of cast aluminum...and if you tighten it too much it will break the cavitation plate on your lower unit.
-
09-13-2015, 04:17 AM #626000 RPM
- Join Date
- Apr 2001
- Location
- Ellicott City, Maryland
- Posts
- 1,328
- Thanks (Given)
- 0
- Thanks (Received)
- 1
- Likes (Given)
- 0
- Likes (Received)
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
So I use my Stream for pulling me through the ski course. It seems as though I want the drag profile to launch flatter if I'm alone in the boat and pulling my friend. I just purchased a High Five and even Bennett Trim Tabs (off CL)that I'm considering installing. I'd modify them to have fins to help reduce my pulling the back end of the boat side to side as I cut around the turn balls. All of this is academic until I get the injectors cleaned and start the engine.
I appreciate the view that Bob's plates are junk and the crack warning. Has there ever been testing or comparison of these plates? Sounds like a great article for John Tiger. He might have done one already. I bought mine over 10 yrs ago and if I remember there were few non-plastic West Marine type plates around. 15 yrs ago I negotiated a cross the "pond" exchange with a machinist-- trim wedges for a custom plate. My end of the deal was upheld and the brit failed to deliver. (Cost as much in shipping as the purchase).
Pat Simmons' custom plate behind his old Quartermaster was an amazing piece of real estate that he fabricated. It would have been more like a swim platform for me. The Bennetts promise an out of the way at speed but greater square inches at takeoff than any cavatation plate add-on. Weight and junking up the transom are the negatives.
Your product looks like a quality piece from your pics. I'd like to have some comparisons before I buy. I guess I have some Pyro in me. He has an exacting way about him and seems to employ the scientific method.
Thanks for for letting me share. Ok, it is 5 am and I need to leave for a 7a ski behind some Mastercrafts.Sea ya, Sleekster
-
09-15-2015, 12:38 PM #635000 RPM
- Join Date
- Jul 2009
- Location
- Texarkana,AR
- Posts
- 363
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 7
- Likes (Received)
- 16
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
My plate is on the way.I got the triad plate.
-
09-15-2015, 01:25 PM #64Screaming And Flying!
- Join Date
- Jul 2004
- Location
- Connecticut
- Posts
- 6,010
- Thanks (Given)
- 465
- Thanks (Received)
- 168
- Likes (Given)
- 911
- Likes (Received)
- 951
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Dirk Pitt should get one of those babies for his ETEC
-
11-21-2015, 08:46 PM #65
dbug......have any plates made up?........i hit you up on fb messenger
81' HYDROSTREAM VECTOR / slightly Modified 200
before and after:http://www.screamandfly.com/showthre...inished!/page3
-
01-30-2016, 12:39 AM #66
Ok the 2016 season will be here before you know so if you want a drag plate let me know TTT !!!
-
05-23-2016, 09:33 PM #67
Are you still making plates ? I need one for my V8 OMC
84 HydroStream Vegas V8
88 Allison XR2002 2.4 EFI BP
00 Mirage Merc 260 LH 15" Mid
69 Uniflite Cruiser Twin 440's
19' Allison Race T2x Mercury
14' Critchfeild 75 Evinrude
13' Allison Race 75 Stinger
-
08-15-2016, 05:17 AM #68
Hi mate how much to ship to Australia 4873for tbe one in the first pic
-
08-16-2016, 04:22 PM #69
I will find out and get back to you asap
-
08-16-2016, 04:49 PM #70
Thanks
-
09-16-2016, 01:14 PM #71
Pm sent james
81' HYDROSTREAM VECTOR / slightly Modified 200
before and after:http://www.screamandfly.com/showthre...inished!/page3
-
06-15-2017, 02:29 PM #72
Get your plate for the 2017 Season !!
-
texasvector liked this post
-
11-12-2017, 10:37 PM #73
Bump TTT
-
texasvector liked this post
-
11-12-2017, 10:56 PM #74
what up
81' HYDROSTREAM VECTOR / slightly Modified 200
before and after:http://www.screamandfly.com/showthre...inished!/page3
-
06-04-2018, 05:37 PM #75New Member
- Join Date
- Jun 2018
- Location
- Orange
- Posts
- 3
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Dbug, I called and left a message today! Needing a plate if your still making them! Thanks