User Tag List
Thanks: 0
Likes: 0
Results 1 to 15 of 17
Thread: Sei lower unit lwp
-
11-16-2014, 07:05 PM #15000 RPM
- Join Date
- Jun 2009
- Location
- Key Largo, Florida, USA
- Posts
- 120
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Sei lower unit lwp
For sale SEI lower unit has maybe 10 hours on the lower and 1 hour on the lwp
$400
-
11-17-2014, 09:39 PM #26000 RPM
- Join Date
- Dec 2011
- Location
- Sunny Oregon
- Posts
- 1,768
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 1
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Prop shaft shear off or just without guts?
-
11-18-2014, 11:55 AM #35000 RPM
- Join Date
- Jun 2009
- Location
- Key Largo, Florida, USA
- Posts
- 120
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Prop shaft shear off worked perfect until the shaft snapped
-
11-18-2014, 11:18 PM #4Screaming And Flying!
- Join Date
- Jul 2002
- Location
- FT WORTH, TEXAS
- Posts
- 8,031
- Thanks (Given)
- 9
- Thanks (Received)
- 146
- Likes (Given)
- 313
- Likes (Received)
- 503
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
is that holes from a blown pinion gear
-
11-19-2014, 10:38 PM #55000 RPM
- Join Date
- Jun 2009
- Location
- Key Largo, Florida, USA
- Posts
- 120
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
No holes that's some paint that came off
-
11-20-2014, 08:07 PM #6
BUMMER no warranty...they have been pretty reliable...did you hit something, did it break at the thrust washer or internally??
-
11-21-2014, 07:38 PM #75000 RPM
- Join Date
- Jun 2009
- Location
- Key Largo, Florida, USA
- Posts
- 120
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Didn't hit anything I ran it for 1 hour after putting the LWP. Broke at the seal
-
11-21-2014, 07:51 PM #86000 RPM
- Join Date
- Dec 2011
- Location
- Sunny Oregon
- Posts
- 1,768
- Thanks (Given)
- 0
- Thanks (Received)
- 2
- Likes (Given)
- 1
- Likes (Received)
- 13
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I had one did the same thing. They don't like being surfaced much
-
11-26-2014, 12:10 PM #9
i have one that just did the same thing too..i think a non ratcheting prop shaft will fit as a replacement. mine has very few hours as well..loosing a prop completly sucks!!
-
11-30-2014, 11:14 PM #10
-
11-30-2014, 11:18 PM #11
-
12-01-2014, 10:12 AM #125000 RPM
- Join Date
- Aug 2006
- Location
- virginia
- Posts
- 666
- Thanks (Given)
- 39
- Thanks (Received)
- 65
- Likes (Given)
- 282
- Likes (Received)
- 732
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
12-19-2014, 05:24 PM #13Junior Member
- Join Date
- Aug 2013
- Location
- United States
- Posts
- 20
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 3
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I just fixed a sei with a lwpu for a customer I had to pull the carrier and shaft at the same time with a slide hammer then air chisel out the shaft back through the carrier as it broke right at the seal like many others, ruining the bearing in the carrier. It was only ran about 3 hours I looked spun welded together I'm no expert buy maybe where the tool steel ends and the stainless begins? I put what I believe is a merc. one piece shaft in it and hoping to different results.
-
12-19-2014, 08:32 PM #145000 RPM
- Join Date
- Oct 2012
- Location
- savannah
- Posts
- 117
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 5
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
I have one of these lowers for sale cheap i have had no problems with it i went to a sporty it may have 2 hours on it .
-
12-19-2014, 11:45 PM #15
does that mean it's a lwp, 20" 187, rh, late mdle, for sale cheap...what does that mean...can't you be more specific...my 2 cents