User Tag List
Thanks: 0
Results 46 to 60 of 64
Thread: 23' Action Marine Restoration
-
11-22-2015, 08:23 AM #46
You are exactly right. The 23' Action was derived from the 25' Action and was the brainchild of Barney senior. We blocked off the mold of the 25' by 23" at the transom. Then, we added an additional 4 degrees of transom angle, added reduced sized lifting strakes behind the original ones closest to the keel and added a reverse chine. The intent was to make the boat faster than the 25' Action for single applications, while incorporating the bottom changes to improve the ride, out of the hole performance and on plane, slow speed cornering and maneuverability. The changes did what we had hoped and even exceeded our expectations. Picked up a significant amount of top end speed in single applications and the ride is incredible, despite the two feet shorter length.
Love mine. It's a boat that can do it all, from river runs to Bahamas trip! As Mr. Action says, the boats run in the 80's with a Monty V-8. Would be interesting to see what a Merc 400 R would do.
Karl
16' Samurai 135hp Johnson sold
16' Banshee 135hp Johnson sold
16' Action Evinrude Strangler sold
21' Olympia 2.6L Johnson sold
18' Critchfield 2.6L Evinrude sold
20' Sanger 3.6L Evinrude V8 sold
19' Action 2.6L / 3.6L V8 Evinrude sold
19' Action 2.7L Evinrude sold
19' Action 3L Johnson sold
25' Action 3.6L Evinrude V8 sold
25' Action Twin 175hp Johnsons sold
25' Action 4L Monty V8 sold
18' Action 115HO E-TEC sold
19' Action 250HO E-TEC sold
23' Action 250HO E-TEC
STV R/R Monty 250HO E-TEC
-
11-22-2015, 08:45 AM #47
man that is great.. great Job! love them
Actions
-
11-30-2015, 06:53 PM #48
What does the bottom look like on these? Is there a large pad, cut out, what? Where do they get the speed numbers from?
-
11-30-2015, 09:01 PM #49
Great info !! I would also like to know from you gurus that have been playing with the setups on the 25s how much set back do these boats like with twin merc outboards? Also 20" or 25" shafts? Where does the prop hub like to be in relation to the running surface? I know the Action Marine guys know how to dial them in for the best top end !!
-
12-01-2015, 05:16 AM #50
whats with the picture on the bottom of these posts, ???????
21 Tuff, Mercury 300X
-
12-01-2015, 09:16 AM #51
A little young and skinny for this old man but still nice.
-
12-02-2015, 03:16 AM #52
-
12-02-2015, 05:16 PM #53
The bottom is a traditional 24 degree vee, no pad, no step. Not sure what speed numbers you are referring to, but here is a link to a Boattest.com test of my 23 Action. With 2 people, test gear, etc. it ran 63.4 MPH and best cruise was at 3500 at 3.79 MPG.
http://www.boattest.com/review/actio...77_23-offshore
Karl
16' Samurai 135hp Johnson sold
16' Banshee 135hp Johnson sold
16' Action Evinrude Strangler sold
21' Olympia 2.6L Johnson sold
18' Critchfield 2.6L Evinrude sold
20' Sanger 3.6L Evinrude V8 sold
19' Action 2.6L / 3.6L V8 Evinrude sold
19' Action 2.7L Evinrude sold
19' Action 3L Johnson sold
25' Action 3.6L Evinrude V8 sold
25' Action Twin 175hp Johnsons sold
25' Action 4L Monty V8 sold
18' Action 115HO E-TEC sold
19' Action 250HO E-TEC sold
23' Action 250HO E-TEC
STV R/R Monty 250HO E-TEC
-
12-02-2015, 05:25 PM #54
We typically set the 25's up with twin 20" engines with about a 15" setback. Most times a B-Bracket or an Armstrong bracket was used, something that provides flotation works well but is not required. Some were set up with twin 25" engines, but to get the best handling and speed, we found the 20" setup worked best. Single engines at about 22' - 29" of setback. Best propshaft height varies depending on what you want to do with the boat, but somewhere around level with the bottom seemed to work well for a lot of applications.
Karl
16' Samurai 135hp Johnson sold
16' Banshee 135hp Johnson sold
16' Action Evinrude Strangler sold
21' Olympia 2.6L Johnson sold
18' Critchfield 2.6L Evinrude sold
20' Sanger 3.6L Evinrude V8 sold
19' Action 2.6L / 3.6L V8 Evinrude sold
19' Action 2.7L Evinrude sold
19' Action 3L Johnson sold
25' Action 3.6L Evinrude V8 sold
25' Action Twin 175hp Johnsons sold
25' Action 4L Monty V8 sold
18' Action 115HO E-TEC sold
19' Action 250HO E-TEC sold
23' Action 250HO E-TEC
STV R/R Monty 250HO E-TEC
-
12-02-2015, 05:49 PM #55
-
12-02-2015, 06:52 PM #56
That is exactly the information I have been looking for. Thank you very much. I have a stainless marine 27" setback with twin 25" mids. They are set too far back to me by the way it handles and balances. I have been looking into finding 20" mids for my mercs but that is proving difficult and expensive, so may go the jack plate route. I am right around 70 now, going to have Simon do some computer tweaking to see if I can hit 80 with the correct setup. Thanks again for your information. I absolutely love my 25
-
12-02-2015, 10:12 PM #57
Karl
16' Samurai 135hp Johnson sold
16' Banshee 135hp Johnson sold
16' Action Evinrude Strangler sold
21' Olympia 2.6L Johnson sold
18' Critchfield 2.6L Evinrude sold
20' Sanger 3.6L Evinrude V8 sold
19' Action 2.6L / 3.6L V8 Evinrude sold
19' Action 2.7L Evinrude sold
19' Action 3L Johnson sold
25' Action 3.6L Evinrude V8 sold
25' Action Twin 175hp Johnsons sold
25' Action 4L Monty V8 sold
18' Action 115HO E-TEC sold
19' Action 250HO E-TEC sold
23' Action 250HO E-TEC
STV R/R Monty 250HO E-TEC
-
12-02-2015, 10:49 PM #58
-
12-03-2015, 05:34 AM #59
Karl
16' Samurai 135hp Johnson sold
16' Banshee 135hp Johnson sold
16' Action Evinrude Strangler sold
21' Olympia 2.6L Johnson sold
18' Critchfield 2.6L Evinrude sold
20' Sanger 3.6L Evinrude V8 sold
19' Action 2.6L / 3.6L V8 Evinrude sold
19' Action 2.7L Evinrude sold
19' Action 3L Johnson sold
25' Action 3.6L Evinrude V8 sold
25' Action Twin 175hp Johnsons sold
25' Action 4L Monty V8 sold
18' Action 115HO E-TEC sold
19' Action 250HO E-TEC sold
23' Action 250HO E-TEC
STV R/R Monty 250HO E-TEC
-
AZMIDLYF liked this post
-
12-06-2015, 09:56 PM #60
Great job, looks damn good man. It's great to see the step by step photos included. Enjoy
1977 Hydrostream Vector 2.5 Promax