User Tag List
Thanks: 0
Likes: 0
Results 1 to 7 of 7
-
03-31-2011, 01:33 PM #1
Junior Member
- Join Date
- Sep 2009
- Location
- baltimore
- Posts
- 6
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
78 235 trim and tilt work on 88 vro 110?
The 235 on the back of my baja 180ss broke a ring and scored the cylinder wall beyond
repair.I have an 88 110 that is missing the trim and tilt.I was wondering if I could swap
the trim and tilt off the 235.Thanks, Jason
-
03-31-2011, 02:52 PM #2
5000 RPM
- Join Date
- Jul 2005
- Location
- Lake County, IL
- Posts
- 761
- Thanks (Given)
- 2
- Thanks (Received)
- 0
- Likes (Given)
- 1
- Likes (Received)
- 4
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
It should, both the manifold and the stern bracket numbers are superceding...
-
03-31-2011, 03:00 PM #3
Junior Member
- Join Date
- Sep 2009
- Location
- baltimore
- Posts
- 6
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Thanks for the fast reply.I will be swapping motors out this weekend and will post back after completion.
-
04-04-2011, 06:50 PM #4
Junior Member
- Join Date
- Sep 2009
- Location
- baltimore
- Posts
- 6
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Got them swapped out this weekend.Everything was the same and fit well.thanks again
-
04-04-2011, 08:45 PM #5
6000 RPM
- Join Date
- Oct 2003
- Location
- LAGRANGE, IL
- Posts
- 1,277
- Thanks (Given)
- 0
- Thanks (Received)
- 11
- Likes (Given)
- 0
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
You will have to do some electrical adapting as well. The 78 motor is a 3-wire motor and uses a remote control box which mounts under the boat's rear splashwell. The 88 trim electrical is setup for a 2 wire motor with two trim relays in a box that mounts on the engine.
-
04-04-2011, 09:15 PM #6
Junior Member
- Join Date
- Sep 2009
- Location
- baltimore
- Posts
- 6
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Oh, forgot to mention.Had to swap trim motors out.Other than that all went well.
-
04-05-2011, 03:31 AM #7
6000 RPM
- Join Date
- Oct 2003
- Location
- LAGRANGE, IL
- Posts
- 1,277
- Thanks (Given)
- 0
- Thanks (Received)
- 11
- Likes (Given)
- 0
- Likes (Received)
- 14
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
You are right on top of the situation!
Reply With Quote
