User Tag List
Results 901 to 915 of 923
-
11-16-2017, 06:09 PM #901Member
- Join Date
- Jun 2017
- Location
- Miami
- Posts
- 68
- Thanks (Given)
- 12
- Thanks (Received)
- 2
- Likes (Given)
- 7
- Likes (Received)
- 19
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Attempted trying out a 3 blade 25p tempest that came with the boat before when it had a 25” shaft and it’s a dog out of the hole and spins it to 6+K RPMs
-
11-18-2017, 01:14 AM #902
Hey Mike whats up? My 28 Promax with 1.75s hits the limiter hard at 6800 and thats at 90mph. The #s are so far off it may be both wet and tired. Sorry for such depressing input. My son ran a 30 promax on a 1.62 last weekend on Greenwood lake and got 97.1. Not sure of his RPM. Something is way off here.
-
11-18-2017, 10:26 AM #903Member
- Join Date
- Jun 2017
- Location
- Miami
- Posts
- 68
- Thanks (Given)
- 12
- Thanks (Received)
- 2
- Likes (Given)
- 7
- Likes (Received)
- 19
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
11-18-2017, 07:19 PM #904
I have 5" of setback and so does Ben. Too much setback takes away from the rough water handling. 5 1/2 is fine.
-
tux974 liked this post
-
11-18-2017, 07:38 PM #905Member
- Join Date
- Jun 2017
- Location
- Miami
- Posts
- 68
- Thanks (Given)
- 12
- Thanks (Received)
- 2
- Likes (Given)
- 7
- Likes (Received)
- 19
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
tux974 liked this post
-
03-31-2020, 01:06 PM #906Member
- Join Date
- Nov 2018
- Location
- South Florida
- Posts
- 32
- Thanks (Given)
- 1
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 9
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
My new to me, restored 22 Velocity CC with a 350 Verado
-
-
04-02-2020, 06:17 AM #907
Great looking rig!
-
04-02-2020, 10:27 PM #908New Member
- Join Date
- Jul 2011
- Location
- Antigua
- Posts
- 3
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 1
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
-
04-06-2020, 03:47 PM #9095000 RPM
- Join Date
- Sep 2003
- Location
- NYC/FL/NH
- Posts
- 279
- Thanks (Given)
- 2
- Thanks (Received)
- 7
- Likes (Given)
- 15
- Likes (Received)
- 41
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Hi guys- putting a 250XS on my 1985 22' velocity. Bought a 5.5" jack plate as well. Quick question- what is everyone running for props? Also, should I put a nose cone on it? Torque Master gear case. Thanks
-
04-06-2020, 07:18 PM #910Junior Member
- Join Date
- May 2013
- Location
- Connecticut
- Posts
- 20
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 1
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
1985 All original? If the transom is good, go with 12" setback if you dont plan on flying in the rough.
I have a 1987 Regal "Velocity". 250efi 5.5" setback and have run choppers, Trophy's and a Solas 4 blade.
The chopper was the fastest 76mph, trophy and Solas handled better but topped out around 72.
- Propshaft height even to 1" ABOVE the pad.
I have a Torque master with 1.62 gears so all my props are low pitch but you dont really need a nose cone unless your faster than 85ish. There's lots of other threads if you search a bit on that topic
If your lower has the 4 holes all the way on the nose of the case your good, just plug the top 6/8 on either side of the case using a 1/4" by 1/4" long set screw from homedepot.
Make sure you have a water pressure gauge and temp gauge.
-
04-07-2020, 01:10 PM #911
Personally I don't like that much setback. The handling suffers in rough water. Your 5.5 will work just fine and also a 24 ProMax may be a good place to start. They work great on Velocitys
-
04-07-2020, 01:12 PM #912
I thought you had a 1.62 but that wasn't you. Whats you ratio?
-
05-19-2020, 11:22 AM #9135000 RPM
- Join Date
- Sep 2003
- Location
- NYC/FL/NH
- Posts
- 279
- Thanks (Given)
- 2
- Thanks (Received)
- 7
- Likes (Given)
- 15
- Likes (Received)
- 41
- Mentioned
- 1 Post(s)
- Tagged
- 0 Thread(s)
Just put the motor on the bracket. My hynautic steering ram is on the front and very close to the transom well. I won't be able to trim much. Any ideas? Right now im at 2.5" below the pad. Should I go up?
-
05-21-2020, 07:48 AM #914
-
07-28-2022, 04:52 PM #915New Member
- Join Date
- Jan 2012
- Location
- miami
- Posts
- 2
- Thanks (Given)
- 0
- Thanks (Received)
- 0
- Likes (Given)
- 0
- Likes (Received)
- 0
- Mentioned
- 0 Post(s)
- Tagged
- 0 Thread(s)
Can some one please tell me the correct height your motor should be mounted on 22 velocity , with no jackplate