Search:

Type: Posts; User: Go Time; Keyword(s):

Page 1 of 40 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    2
    Views
    74

    I may have a clean set. I can remember if they...

    I may have a clean set. I can remember if they have the bolt on water jackets or are the lost foam style. what you are looking for?
  2. Replies
    2
    Views
    63

    PM sent

    PM sent
  3. Replies
    5
    Views
    79

    You need what they call the "blue" harness if you...

    You need what they call the "blue" harness if you are still running the 8 pin harness. The 300X is already wired at the powerhead and the connector is at the bottom, front, starboard side under the...
  4. Mercury Tech: Jeff, I know this sounds too simple, but I would...

    Jeff, I know this sounds too simple, but I would look at grounds and connections. If they all check, then look for a chafed wire against the block. These intermittent things can be the hardest to...
  5. Mercury Tech: When you say you have no fire until it cools , do...

    When you say you have no fire until it cools , do you mean you verified that you have no ignition (spark) or just that the engine won't start.
  6. looks like a smallshaft torquemaster, does the...

    looks like a smallshaft torquemaster, does the gear lube drain from the carrier?
  7. Replies
    8
    Views
    334

    Still got it...

    Still got it...
  8. Replies
    16
    Views
    2,822

    The only piston I know of for a 2.5L 225 Promax...

    The only piston I know of for a 2.5L 225 Promax oversized with 1.5mm rings are WSM pistons....very nice piece. I run them in several of my Promaxes. I'm pretty sure Chris uses the as well.
  9. Replies
    13
    Views
    281

    Crank position sensor. With the 04 300X you will...

    Crank position sensor. With the 04 300X you will get alarms for a ton of conditions....the two obvious were mentioned (low oil and water in fuel). Also will get a alarm for a sensor out of range...
  10. Replies
    3
    Views
    414

    You will have the call Pat, not sure he will...

    You will have the call Pat, not sure he will split up the mid.
  11. Replies
    3
    Views
    414

    Cowls have sold.... Midsection still available.

    Cowls have sold....

    Midsection still available.
  12. Thread: LH 28" Chopper

    by Go Time
    Replies
    0
    Views
    46

    LH 28" Chopper

    A friend has a Counter rotating 28" pitch Mercury racing chopper small shaft. Prop has never been touched and has no nicks or dings. $200
    Contact him directly 757-508-0199
  13. Replies
    3
    Views
    414

    Bridgeport Offshore Mid and cowl set

    A friend has a complete Offshore mid section with clamp bracket, exhaust adapter and 20" ridgeback offshore can from a 1991 bridge port. The mid was clean when I saw it.
    He's asking 1K$ negotiable....
  14. Replies
    8
    Views
    334

    I'm sure someone can use a good 824003...

    I'm sure someone can use a good 824003 box....good for any of the 36# XRI systems
  15. Why would you remove the oil injection on a 2003...

    Why would you remove the oil injection on a 2003 ?...I assume it has an electric oil injection pump with crankcase oil injection that was standard.
  16. You need to keep the RPM in the 6500 range to use...

    You need to keep the RPM in the 6500 range to use all your power. I agree on a using a bravo if they make it in a low enough pitch
  17. Replies
    56
    Views
    1,156

    all three, six jets total...they are under the...

    all three, six jets total...they are under the brass hex caps on top of the carb (one each side)
  18. Mercury Tech: 12.4 volts is plenty. Check the pulse pump...

    12.4 volts is plenty. Check the pulse pump diaphragm for a hole that will cause excessive fuel to enter the intake at low speed and flood you out. This usually has little affect at higher speeds as...
  19. Replies
    56
    Views
    1,156

    double post...sorry

    double post...sorry
  20. Replies
    56
    Views
    1,156

    With the WH-28 carbs, try reducing the idle air...

    With the WH-28 carbs, try reducing the idle air jets to .048, it problably has .056 in it now, that should help the lean sneeze at idle and improve hole shot. you may need to try several different...
  21. Mercury Tech: Next time it happens, check to make sure the HP...

    Next time it happens, check to make sure the HP fuel pump is running. I had a Promax and when the ECU would heat when the engine ran a while, the pump driver would quit.
  22. Replies
    12
    Views
    388

    Is it a 20" motor and if so, do you still have...

    Is it a 20" motor and if so, do you still have the complete midsection & clamp bracket with trim?
  23. Replies
    8
    Views
    334

    But you still need the reed blocks....

    But you still need the reed blocks....
  24. Replies
    8
    Views
    334

    Bobby, the only thing I need is a Promax intake...

    Bobby, the only thing I need is a Promax intake with reed blocks....you got?
  25. Replies
    8
    Views
    334

    Mercury 200HP ECU

    Mercury 200HP ECU for 2.5L motors. Its a 824003A30 xri type ECU and should work on 1996 to 2001 200 EFI motors. Worked when removed and ECU has been checked out. Has good pump driver and DDT scan...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
Diamond Marine