Search:

Type: Posts; User: Go Time; Keyword(s):

Page 1 of 40 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    5
    Views
    132

    I sent you a PM Lee...sounds good!

    I sent you a PM Lee...sounds good!
  2. You may want to post this on the buy and sell...

    You may want to post this on the buy and sell forum...parts wanted section
  3. We use the tunnel tab on my buddies' Spectre

    We use the tunnel tab on my buddies' Spectre
  4. Replies
    16
    Views
    603

    I agree with you Bud....the buyer protection...

    I agree with you Bud....the buyer protection provided by Paypal is a good thing when doing business on the web. It seems to be the standard these days. I recently sold an engine and the buyer didn't...
  5. Replies
    3
    Views
    59

    My understanding is that the thermostats control...

    My understanding is that the thermostats control idle temperature and poppet controls temp at higher speeds. Try new stats first.

    There is a small inline filter in the oil supply line to the tank...
  6. Replies
    5
    Views
    147

    300x blocks are crank case injected...250s are...

    300x blocks are crank case injected...250s are XRI, in addition to other differences mentioned.
    Some 250s do not have exhaust notch.
  7. Replies
    1
    Views
    39

    Mercury Tech: Found it...CDI part # 451-9601 for 6 FT extension...

    Found it...CDI part # 451-9601 for 6 FT extension and 451-9602 for 10 FT extension.
  8. Replies
    7
    Views
    268

    Well, I'm pleased to report that the gear case...

    Well, I'm pleased to report that the gear case has showed up AND Titus finally call my friend. So all is well,,,and don't underestimate the power of S&F.
    Thanks Tux also...
  9. Replies
    1
    Views
    39

    Mercury Tech: Promax ECU extension harness

    I recently saw an extension harness for the promax 824003 style ECU so the ECU can be put in the boat...checked several sites like Brucato, DBR, CDI and I can't find it,...Anyone know where I can...
  10. Replies
    5
    Views
    132

    PMs sent to both... Thanks for the replies

    PMs sent to both...
    Thanks for the replies
  11. Replies
    5
    Views
    132

    Need a Promax ECU and set of heads

    I'm going to build another powerhead and I will need an ECU for the ProMax 824003 A17, A23 or A32 (I think these are the right numbers for Promax ECUs).
    Also need a set of stock (uncut) heads 18789...
  12. Replies
    36
    Views
    876

    Mercury Tech: Don't use the washer on the poppet and also I...

    Don't use the washer on the poppet and also I recommend you peen the hard plastic seat in the block. That's what prevents it from becoming unseated. You can't just drive the new one in.
  13. Replies
    36
    Views
    876

    Mercury Tech: The kits in the first two links are not correct....

    The kits in the first two links are not correct. That tall plastic cup piece is not used, should use flat black plastic washer like the second photo in the Ebay add.
  14. Replies
    36
    Views
    876

    Mercury Tech: I don't think you use the plastic washer on the...

    I don't think you use the plastic washer on the poppet for your setup which would increase spring preload. Check the parts breakdown for your model year. Also. make sure the hard seat is peened in...
  15. Replies
    5
    Views
    226

    The pump is turned on by the ECU and it takes the...

    The pump is turned on by the ECU and it takes the black/red lead from the pump to ground. You either have a short to ground on that lead or the driver in the ECU is shorted to ground would be my...
  16. Replies
    36
    Views
    876

    Mercury Tech: Well it was definitely your poppet. Did you use a...

    Well it was definitely your poppet. Did you use a soft diaphragm? Also you should not use the washer between the valve and spring. It could be binding if not properly reassembled.
  17. Replies
    3
    Views
    193

    I have a friend with a lower unit at Titus and he...

    I have a friend with a lower unit at Titus and he has not been able to reach him either, and he has left several messages.... apparently communications is not his thing. I'm sure he must be very...
  18. Replies
    7
    Views
    268

    Tux, There must be a problem, he said today that...

    Tux, There must be a problem, he said today that he has called many times (almost daily as this point) and left a bunch of messages and no response. The CLE has been there since May, how long does it...
  19. Replies
    7
    Views
    268

    Thanks for the insight Greg...I will let my...

    Thanks for the insight Greg...I will let my friend know. I think expected a bit more communication.
  20. Replies
    7
    Views
    268

    Custom Marine & Welding.... ?

    Is Titus still in business doing nose cones, I friend sent a CLE for a cone job in May and hasn't got it back. More concerning is he can't seem to get anyone to answer the phone or to return a...
  21. Replies
    6
    Views
    1,330

    Sold, Thanks S & F

    Sold, Thanks S & F
  22. The factory twin 21 we had came with wing plates,...

    The factory twin 21 we had came with wing plates, transom mounted rams and Hynautic steering. But it had Bridgeports.
  23. Replies
    6
    Views
    1,745

    Its almost is pretty as this one...Bump the...

    Its almost is pretty as this one...Bump the Daytona

    323979
  24. Replies
    6
    Views
    830

    Yes, you can contact the seller by calling the...

    Yes, you can contact the seller by calling the phone number in the thread .
  25. Replies
    6
    Views
    1,330

    Southeast VA

    Southeast VA
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
Diamond Marine