Search:

Type: Posts; User: myron; Keyword(s):

Page 1 of 25 1 2 3 4

Search: Search took 0.13 seconds.

  1. Thread: 2.5 reed plate

    by myron
    Replies
    3
    Views
    140

    Brad call me tomorrow I am pretty sure I still...

    Brad call me tomorrow I am pretty sure I still have one. 321-288-8237 Myron
  2. captain silver with ginger ale and a splash of...

    captain silver with ginger ale and a splash of coconut rum
  3. Replies
    13
    Views
    331

    Mark I have a brand new in the box. The part...

    Mark I have a brand new in the box. The part Number is 2717-827352T 3, I think this was for the first 280s I don't know if it is the same as what you are looking for
  4. Replies
    18
    Views
    867

    I have Mallory switch boxes and a Brucato ACU on...

    I have Mallory switch boxes and a Brucato ACU on my 225 and it runs great
  5. from what I have been told none of the optis are...

    from what I have been told none of the optis are clean enough, funny thing is Yamaha did the same thing in the motocross world and ruined it. Before if you 2 stroke bike blew up it would take about...
  6. from what I have herd the 2 strokes from Mercury...

    from what I have herd the 2 strokes from Mercury are done
  7. Replies
    3
    Views
    787

    sent PM

    sent PM
  8. Replies
    8
    Views
    649

    not true I had a 1991 EFI with relief slots and 7...

    not true I had a 1991 EFI with relief slots and 7 peddle front
  9. make sure your driveshaft is not pitted where the...

    make sure your driveshaft is not pitted where the seal area is
  10. Mercury Tech: check your trigger I just had one do the same...

    check your trigger I just had one do the same thing
  11. Glenn Reynolds use to do real well back in the...

    Glenn Reynolds use to do real well back in the mod vp days
  12. Replies
    5
    Views
    162

    or it could be your gauge, I would think it is...

    or it could be your gauge, I would think it is OK, unless you are having issuses
  13. I could be wrong but I believe the 2.5 case and...

    I could be wrong but I believe the 2.5 case and the 3.0 case have a different profile
  14. You say you ran that high with the 2.5, but with...

    You say you ran that high with the 2.5, but with what case, also from my experience no 2 sportmasters are the same, and the sportmaster has a lot of stern lift built into it.
  15. for what it is worth, I have been running an...

    for what it is worth, I have been running an Allison since the early 90's, when I used to play with top end runs I never found it beneficial to run with the prop shaft higher than the pad, I know...
  16. just curious as what your setup was?

    just curious as what your setup was?
  17. Glad it was not worse, do you know for sure it...

    Glad it was not worse, do you know for sure it was the gearcase or did you chop the throttle, or maybe to much negative trim. I have been thinking about a 3.0 also.
  18. Replies
    12
    Views
    349

    the last time I was at the lake before it closed...

    the last time I was at the lake before it closed the only ones I ever got were 6"
  19. Replies
    12
    Views
    349

    6" I just measured one

    6" I just measured one
  20. Thread: Promax rebuild

    by myron
    Replies
    16
    Views
    865

    not true, jay did a pro max block and front half...

    not true, jay did a pro max block and front half for me, I put it together myself.
  21. Yamalube 2-R is one of the best 2 stroke oils made

    Yamalube 2-R is one of the best 2 stroke oils made
  22. Thread: trim switch

    by myron
    Replies
    5
    Views
    275

    Mercury Tech: more than likely it is the switch on the cowl,...

    more than likely it is the switch on the cowl, they go bad often
  23. Replies
    3
    Views
    171

    40 amp regulators

    who makes them other than Mercury
  24. Replies
    12
    Views
    532

    Mercury Tech: I just had an issue, come to find out it was a...

    I just had an issue, come to find out it was a bad spark plug. sometimes the most simple thinks are overlooked
  25. Replies
    6
    Views
    278

    I made some aluminum plates to fit over the holes...

    I made some aluminum plates to fit over the holes on the under side, outside of the housing. you drill and tap 1/4 -20 for bolts from the bottom, it worked great
Results 1 to 25 of 619
Page 1 of 25 1 2 3 4
Diamond Marine